• 100W-58P VU series.png

100W AC-DC Constant Voltage LED Driver


AC input range from 90 to 264Vac Constant voltage mode Active PFC design No-load power consumption <0.5W at 230Vac Set up time < 0.5S at 230Vac Compliant with ErP (EU) 2019/2020 Compliant with CE certificate by LED driver product segment Safety protections include OCP/SCP/OVP/OTP 3 years warranty

Product Specification

  Model No.                           LD100H-VU83012-58P  LD100H-VU42024-58P  LD100H-VU28036-58P  LD100H-VU21048-58P
Output DC Voltage 12V 24V 36V 48V
Current Range 0~8.30A 0~4.20A 0~2.80A 0~2.10A
Rated Power 99.6W 100.8W 100.8W 100.8W
Voltage Tolerance ±5% ±5% ±5% ±5%
Ripple & Noise (Max. full load) note.2 0.20Vp-p 0.20Vp-p 0.36Vp-p 0.48Vp-p
Efficiency note .1 full load(230V/50HZ) ≥88% ≥ 90% ≥90% ≥90%
Max Input Power@ No Load <0.5W@Vin_ac=230V
Setup Time ≤500mS @ 230Vac & Full load
Hold up Time (Typ.) 20mS @ 230Vac & Full load
Input Voltage Range 100 - 240Vac
Frequency Range 50/ 60 Hz
AC Current (Max.) 1.1A at 115Vac ; 0.52A at 230Vac
Power Factor > 0.95 at 230Vac with full load.
Inrush Current (Max.) 75A at 230Vac
Leakage Current < 1mA/ 240Vac
Protections Over Current 110% - 150% Rated max output current.
Short Circuit Hiccup mode, recovers automatically after fault condition is removed
Over Temperature Shut down output, recovers automatically after temperature goes down
Over Voltage 110% - 150% Rated output voltage
Environment Working Temp -20oC ~ 50oC (Refer to output load derating curve)
Working Humidity 20% ~ 90% RH non-condensing
Storage Temp, Humidity -40 ~ +80oC, 10% ~ 90% RH
Safety&EMC Safety Standards EN61347 ‐ 1, EN61347 ‐2 ‐ 13
Withstand Voltage I/P - O/P : 3.75KV AC
Isolation Resistance I/P - O/P : 100M ohms / 500VDC @25oC
EMI Conduction & radiation Meet EN55015
EMS Immunity EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547, EN61000 ‐3 ‐2 Class C
Connection Input HO5RN-F 2*1.0mm^2(200 mm)      
Output HO5RN-F 2*1.0mm^2(120 mm)      
Others MTBF 100K hours min. MIL -HDBK -217F(25℃)      
Dimension(L*W*H) 188x53.6x30mm      
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C ambient temperature. 2. Ripple & Noise are measured at 20MHz bandwidth oscilloscope and with 0.1uF & 47uF paralleled capacitor.      
3. The power supply is considered a component which will be installed a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.      

Key words:

100W AC-DC Constant Voltage LED Driver

Online Message

Dear customers, if you have any comments and suggestions on our products or services, please tell us in time, we will give you satisfaction as soon as possible