Home

100W AC-DC Constant Voltage LED Driver

Classification:

Universal AC input /Full range (up to 264 VAC) Class 2 Power Supply Unit. Constant Voltage design Fully isolated plactic case Protections : OLP / SCP / OTP / OVP 3 years warranty

Message

Spec Sheet

Product Specification

Model No.		LD100L-VU85012-58	LD100L-VU42024-58
Output	DC Voltage	12V	24V
	Current Range	0~8.5A	0~4.2A
	Rated Max. Power	102W	100W
	Voltage Tolerance note.3	±6%	±5%
	Ripple & Noise (Max.) note.2	0.15 Vp-p	0.15 Vp-p
	Efficiency(Typ.) note.1	83%	86%
	Setup Time note.6	1000ms/230Vac at full load
Input	Voltage Range note.4	100 - 240VAC
	Frequency Range	50 / 60Hz
	AC Current (Max.)	2.0A at 115VAC / 1.2A at 230VAC
	Inrush Current (Max.)	75A at 230VAC
	Leakage Current	< 0.5 mA / 240Vac
Protections	Over Load	110% - 160% Constant current limiting, auto-recovery
	Short Circuit	Hiccup mode, recovers automatically after fault condition is removed
	Over Temperature	Shut down o/p voltage,recovers automatically after temperature goes down.(Tcase: 90±10℃)
	Over Voltage	130% ~ 160% rated output power Type : Recover Mode
Environment	Operation Temp.	-20℃ ~ 60℃ (Refer to output load derating curve)
	Operation Humidity	20% ~ 90% RH non-condensing.
	Storage Temp	-40℃ ~ +80℃
	Storage Humidity	10% ~ 95% RH
Safety & EMC	Safety Standards	EN61437-1,EN61437-2-13 Approved. ; IP67 design refers to EN60529.
	Withstand Voltage	I/P - O/P : 3K VAC
	Isolation Resistance	I/P-O/P : 100M ohms / 500VDC at 25 ℃
	EMI Conduction & radiation	meet EN55015
	EMS Immunity	meet EN61000-4-2, 3, 4, 5, 6, 11 ; EN61547
Connection	Input	UL rated, 1015 18 AWGx 2 C( 150 mm)
	Output	UL rated, 1015 14 AWGx 2 C( 150 mm)
Others	MTBF	200K hours min. @Ta=25 ℃
	Dimension (LWH)	187.5 * 52 * 37 mm
	Packing (LWH) / Carton	290 * 340 * 230 mm ; 25pcs / 16.5Kg
Note	1. All parameters NOT specially mentioned are measured at 230V AC input, rated load and 25°C ambient temperature. 2. Ripple & Noise are measured at 20MHZ of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf paraliel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Dlrective on the complete installation again. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit. 8. Suitable for indoor use or outdoor use without direct sunlight exposure.

Key words:

100W AC-DC Constant Voltage LED Driver

None

Online Message

Dear customers, if you have any comments and suggestions on our products or services, please tell us in time, we will give you satisfaction as soon as possible